The Everchill RV refrigerators we carry do not have an integrated water filter. Any filter would need to be an external version like the AquaFresh Exterior RV Water Filter - Qty 2 # A01-1132VP. This is an in-line filter with your water connections.
We don't currently carry the model you referenced, but based on my research it doesn't have an integrated filter. view full answer...
Innovative technology in Curt's Echo trailer brake controller # C51180 makes it by far the easiest trailer brake controller available for any vehicle that has a 7-way connector, whether a motorhome or a passenger car.
The Echo avoids all concerns with compatibility with the changing factory wiring in motorhomes and other vehicles. You will simply plug it into the 7-way, pair it to your phone and plug the trailer into the Echo and you're done. Please check out the linked video.
This unit... view full answer...
Yes, the Demco Air Force One Supplemental Braking System for Freightliner Chassis Motorhomes with BrakeSync # DM23MV will come with a set of instructions, and will actually even come with an instructional CD included to help with the installation and usage.
I've also attached a short video below where Ryan goes over the installation he did with a 2022 Ford Escape view full answer...
With weight distribution systems like the Curt part # C17062 the reason backing up isn't recommended is because if you jackknife the trailer the spring bars will either pop out of the system with a lot of tension/force or a component of the system will bend/break.
So what you can do is back up basically totally straight with the system installed or you can remove the bars before making tight turn maneuvers. view full answer...
The feet on your motorhome's landing gear should not be bent at all, and for a SnapPad like the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet # SP54FR4 you're looking to fit, it's going to need to be replaced.
For instance, if you had a Lippert Landing Gear and needed a replacement 9" foot to work with the SnapPads mentioned above, you'd need the Lippert 5th Wheel RV Landing Gear Foot Pad # LC314667. view full answer...
Depending on your type of toy hauler, the Classic Accessories Toy Hauler Screen, # 052963799941 may be installed on the outside or inside of the rear door frame. view full answer...
The Everchill RV Refrigerator w/ Freezer part # 324-000119 is reversible so you can remove the door and install the hinge on the opposite side or simply remove the door for cleaning. I don't have an exact write-up for this process but it would be no different than removing the door from the refrigerator in your home. You'll first locate the hinge and use the appropriate tool for said fasteners which attach the hinge to the body. The fastener heads are likely covered with plugs you'd have... view full answer...
From how you're describing your set up, it sounds like your bumper is attached to a tube frame, and there is a way for you to install the support brackets, which are the following part number:
- Mount-n-Lock SafetyStruts Universal RV Bumper Support Brackets # MO34VR
What you'll need to do is drill small holes into the tube frame, and then use the included self-tapping bolts to mount the brackets. I have added cut outs from the instructions which show how the brackets install to a tube... view full answer...
The ThermaHeat RV Holding Tank Heater Pad w/ Thermostat # 277-000163 is compatible with 12 volt DC power but can be used with a converter to adapt to AC power. This pad is designed to be used on holding tanks with capacities between 29 and 40 gallons and simply sticks onto your tank. view full answer...
If you are using the Single-Axle Trailer Hanger Kit part # APS3 with the 3-Leaf Double-Eye Spring part # e59SR then you will need to install the leaf springs hangers 22-7/8" apart. In regards to spacing front to back, I have attached a help article for you that will help with this. view full answer...
Thank you for providing that picture. In order to install the # SSR54FR on your Dometic AC you will start by removing the white wire coming from the compressor to the run capacitor and connect it to the blue wire on the SoftStartRV. Next, take the black wire from the SoftStartRV and connect it where the white wire was on the run capacitor.
The yellow SoftStartRV wire will connect to the red wire at the run capacitor that goes to the compressor. If there is a 2nd red wire going to the... view full answer...
To be effective you only have to replace one hinge of your RV entry door with the Replacement Controlled Motion Hinge for RV Entry Door # LC22NJ. You would not have to replace them all. view full answer...
According to the owners manual for your 2024 Chevy Trax disconnecting the battery is the only option to prevent the parking brake from activating when you flat tow your vehicle. We have the Battery Disconnect # RM-766 which can be used for this purpose. This will allow you to disconnect the battery with the push of a button. view full answer...
If only the axle is bent then you can go with just a new axle and reuse all of the other components like the hubs, bearings, brake assemblies, etc. To pick out the correct replacement axle you will need to get the hub face to hub face dimension of your axle as well as the spring seat center to spring seat center and the axle weight capacity.
I don't have a way to look that up so you'd have to get me that info and I can see if it's an axle we carry or one that you'd have to order locally.... view full answer...
I may have an option for you, but we do not have a breakdown of which axle your 2019 Forest River Rockwood Geo Pro 15TB Travel trailer uses so you will need to measure the axle, and determine its rating.
Starting with measuring the axle you will need to measure from hub face to hub face, and from spring center to spring center. This will tell us the length of the axle needed, and how wide the frame of your trailer is.
For the axle rating the easiest way to get this is looking for the... view full answer...
There isn't a heat sink available for the Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D and there isn't really one necessary. It has been tested thoroughly and it does not put off enough heat to require that. view full answer...
The Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K comes pre-lubed which means the bearings are already packed for you but you would still want to add extra grease to the spindle and then fill the hubs as needed prior to use. If you don't already have some compatible grease I would simply recommend ordering the Marine Wheel Bearing Grease part # L154FR which comes in 3-3oz cartridges that you can use with or without a grease gun. The color of the grease won't matter as far as compatibility... view full answer...
While we would not have any way to know for sure it is unlikely there is going to be wiring run.
In order to install the MaxxAir MaxxFan Trailer Roof Vent # MA00-06200K you would need to use Primary Wire - 16 Gauge # DW02359-1 to run wire to a 12V power source.
This vent is designed to fit standard RV roof openings of 14” x 14” and a minimum roof thickness of 1-1/8” to a maximum of 6-1/2”; it will also require the use of Sealant # 0160297 to ensure a tight bond between the flange and roof. view full answer...
The Aluminum Hi-Spec Series S5 Trailer Wheel - 13" x 5" Rim - 5 on 4-1/2 - Silver # AM22323HWT will work well on your 2008 Flagstaff MAC 228D. You will not need to remove the current lug studs and trade them out. The current ones will work just fine. There are steel inserts in the aluminum wheels so they will keep the lug nuts from coming loose over time. I recommend using the Lionshead Trailer Wheel Lug Nut - 1/2"-20 - Stainless Steel # LHLR103. You may also want the locking set #... view full answer...
The Everchill RV Refrigerator w/ Freezer # EV77FR doesn't come with mounting brackets, but I have seen people just some heavier-duty L-brackets and screw it into the back of the unit at the bottom and then in the floor to prevent the fridge from moving. view full answer...
Go To Results